一、滚珠丝杆支撑座结构：

1、 Ball screw support seat structure:

1、支撑座有8个型号，对标准滚珠螺杆库存品的轴端、成品，预备了标准化的支撑座 EK、 EF、FK、FF型，对一般滚珠螺杆预备了标准支撑座AK、AF、BK、BF型。

1. There are 8 models of support seats available, including standardized support seats EK, EF, FK, and FF for standard ball screw inventory and finished products, and standard support seats AK, AF, BK, and BF for general ball screws.

2、固定侧装有经预压调整的JIS5级或P0级的角接触滚珠轴承，可依选用螺杆等级做符合经济的搭配。滚珠丝杠认准钛浩，高精度稳定的回转性能。

2. The fixed side is equipped with JIS5 or P0 grade angular contact ball bearings that have been pre pressed and adjusted, and can be economically matched according to the selected screw grade. The ball screw recognizes the titanium Hao, with high-precision and stable rotational performance.

3、支撑侧使用深沟槽滚珠轴承。

3. Deep groove ball bearings are used on the support side.

4、支撑座EK、BK、FK和AK型的内部轴承含有适量的锂皂基润滑脂，用特殊密封。所以这些型号能够长期使用。

4. The internal bearings of the support seats EK, BK, FK, and AK contain an appropriate amount of lithium soap based grease and are sealed with a special seal. So these models can be used for a long time.

二、滚珠丝杆支撑座的安装：

2、 Installation of ball screw support seat:

1、将固定侧安装到螺杆上。

1. Install the fixed side onto the threaded rod.

2、将固定侧插入，拧紧锁紧螺帽，用垫块和内六角固定螺栓将其固定。

2. Insert the fixed side, tighten the locking nut, and secure it with a cushion block and an internal hexagonal fixing bolt.

3、支撑侧轴承用止动环固定到螺杆轴上，并装入支撑侧支撑座。

3. The support side bearing is fixed to the screw shaft with a stop ring and installed into the support side support seat.

导轨丝杠厂家要你注意：

The manufacturer of guide rail screws should pay attention to:

注1：请勿将支撑单元拆解。

Note 1: Do not disassemble the support unit.

注2：螺杆轴插入支撑单元时，注意请不要将油密封垫片的凸缘球翻。

Note 2: When inserting the screw shaft into the support unit, be careful not to flip the flange ball of the oil sealing gasket.

注3：用内六角固定螺栓压紧垫块时，为防止松弛请将内六角固定螺栓涂上粘结剂後再拧紧。

Note 3: When using the hexagonal fixing bolt to compress the cushion block, to prevent looseness, please apply adhesive to the hexagonal fixing bolt before tightening.

另外在严酷的条件下使用时，还必须采取措施防止其他零部件的松弛。

In addition, when used under harsh conditions, measures must also be taken to prevent relaxation of other components.

三、工作台程基座上的安装：

3、 Installation on the workbench base:

1、使用支座把滚珠螺杆螺帽安装在工作台时，将螺帽插入支座并暂时拧紧。

1. When installing the ball screw nut on the workbench using a support, insert the nut into the support and temporarily tighten it.

2、将固定侧暂时拧紧到基座上。这时，请将工作台靠近固定侧支撑单元并对准轴，调整工作台使基能平滑移动。以固定侧为基准时，请调整滚珠螺杆螺帽与工作台或支座内之间保持一定间隙。以工作台为基准时，用薄垫片调整（角型支撑单元用）、或将螺帽外表面与安装部内面之间 留一定间隙（圆型支撑座用）进行调整。

2. Temporarily tighten the fixed side to the base. At this point, please place the workbench close to the fixed side support unit and align it with the center of the shaft, and adjust the workbench so that the foundation can move smoothly. When using the fixed side as the reference, please adjust the ball screw nut to maintain a certain gap between the workbench or support. When using the workbench as a reference, adjust with thin shims (for angle support units) or leave a certain gap between the outer surface of the nut and the inner surface of the installation part (for circular support seats) for adjustment.

3、将工作台靠近固定侧支撑单元，并对准轴，使工作台往返数次，一直调整到螺帽整个行 程都能平滑运动，并暂时将支撑座拧紧在基座上。确认精度及完全拧紧支撑单元用千分表一边测试滚珠螺杆轴端的摆动及轴向间隙，一边按顺序完全拧紧滚珠螺杆的螺帽、 螺帽支座、固定侧、支撑侧。

3. Place the workbench close to the fixed side support unit and align it with the center of the shaft, allowing the workbench to travel back and forth several times until the entire stroke of the nut can move smoothly, and temporarily tighten the support seat on the base. Confirm the accuracy and fully tighten the support unit. Use a dial indicator to test the swing and axial clearance of the ball screw shaft end while fully tightening the nut, nut support, fixed side, and support side of the ball screw in sequence.

四、与马达的连接

4、 Connection to motor

1、将马达支座安装到基座上。

1. Install the motor support onto the base.

2、用联轴节将将马达与滚珠螺杆连接起来。(注意安装精度)

2. Connect the motor to the ball screw using a coupling. (Pay attention to installation accuracy)

3、请注意进行充分的试车运行。

3. Please pay attention to conducting sufficient trial operation.

4、请注意清洗台面。

4. Please pay attention to cleaning the countertop.

滚珠丝杆支撑座的安装事项就讲解到这里了，希望能够给您好的帮助，更多事项就来我们网站http://www.jngongrun.com咨询！

That's all for the installation of the ball screw support seat. I hope it can be of great help to you. For more information, please come to our website http://www.jngongrun.com consulting service